The water vapor transmission permeability of a polyethylene bottle refers to the amount of water vapor transmission through a sample within a certain time under a specified temperature, relative humidity, and a certain water vapor pressure difference.     The amount of water vapor transmission  permeability of a solid bottle at a specified temperature, relative humidity, and a certain water vapor pressure difference.     The water vapor transmission permeability  of the liquid bottle is within the specified temperature and relative humidity environment, and the percentage of water loss in the bottle within a certain period of time.     The water vapor permeability measurement methods are: cup method, electrolytic analysis method,Weight method.     The water vapor transmission rate of polyethylene bottles actually includes the two meanings of water vapor transmission  permeability and water vapor transmission coefficient. The meanings expressed by these two meanings also have certain differences, but they can be used to represent water vapor transmission. Ability to grow materials.     The water vapor transmission permeability indicates the weight of water vapor transmission material under a certain time, under certain temperature and humidity conditions. The water vapor transmission rate is the standard value of the water vapor transmission rate converted by the coefficient, and corresponds to the standard unit,     Used for comparison between different test results.     GBPI's star products are: precise laboratory instruments such as water vapor transmission rate tester, oxygen transmission rate tester, gas transmission rate tester, etc. More industry knowledge of transmission rate test instruments will be updated next time, more For more details, please pay attention to our official website.

vapor permeation refers to the phenomenon that water vapor molecules penetrate and diffuse from the side with high partial pressure to the side with low partial pressure when the partial pressure difference of water vapor exists on both sides of the envelope. The amount of steam penetration is directly proportional to the breathability of the material of the envelope structure and the difference in partial pressure of steam on both sides, and inversely proportional to the thickness of the structure. vapor permeation is a new gas-phase dehydration membrane separation process. It is based on steam feed. Under the impetus of the partial pressure difference of each component in the mixture, the use of each component in the membrane to dissolve and expand the difference in performance to achieve The mixture separates. The application of vapor permeation technology in the separation of near boiling point, constant boiling point and isomers has its unique advantages, and it can also be coupled with biological and chemical reactions. The continuous removal of the reaction products has significantly improved the conversion rate of the reaction. Its technical and economic advantages are obvious, and it has broad application prospects in industrial fields such as petrochemicals, medicine, food, and environmental protection. GBPI's main products are: water vapor transmission rate tester, oxygen transmission rate tester, gas transmission rate tester, mask detection tester, nozzle bag sealing machine, electronic tension machine etc. If you need to know more product details, please click below to consult.

    BFE is an indicator tested by Labs in Salt Lake City, Utah, USA. It refers to the filtration efficiency of bacteria in maks testing. The test used Staphylococcus aureus with an average particle size of 3 μm as the object. Most BFE masks use polypropylene (PP) as the main protective material. Mainly improve the durability of the mask. Please note that it is "durability", not "protection". Since the standard only uses 3µm test samples, we cannot know in detail the ability of BFE masks to protect against viruses below 3µm. As I said above, the diameter of the droplet is 1~5μm. This is not to say that BFE masks are not anti-virus, but the standards used in the tests are relatively loose. We cannot quantify the protective effect of this mask on coronavirus, but the BFE test does protect the bacteria. It is standard, so if you only prevent the spread of coronavirus, there is no problem. If you are not sure, please use other standard masks.     N95 is not a specific product name. As long as it meets the N95 standard, and products that pass the NIOSH review can be called N95 masks. This standard is one of 9 types of particle protective masks certified by the National Institute of Occupational Safety and Health (NIOSH). "N" indicates oil-resistant particulate matter, and "95" indicates the filtration efficiency of particles with an aerodynamic diameter ≥ 0.3 μm. Above 95%, it can effectively filter out non-oily particles, such as dust, acid mist, paint mist, microorganisms, etc. As can be seen from the above, the N95 mask can prevent coronavirus.     Generally speaking, the higher the protective performance of the mask, the greater the impact on the comfort performance. When people wear masks to inhale, the masks have a certain resistance to the flow of air. When the inhalation resistance is too large, some people will feel dizzy, chest tightness and other uncomfortable conditions. Therefore, the basic principle of wearing a mask is to wear it scientifically and reasonably, to use it in a standardized manner, and to effectively protect it.

Application Medical mask testing Textile material testing Laboratory related tests Standard EN 14683 Functional advantages Built-in touch screen and micro printer High-precision differential pressure sensor, digitally displays the differential pressure across the sample Manual control of air flow and time Pressure sensor, gas quality controller can be calibrated and measured Theoretical method The output of the air flow is set by a gas flow meter, the air flow passes through a certain area of the test sample, the current pressure is detected by a pressure sensor, and the pressure difference is calculated. Technical index Item Technical Parameter Pressure Sensor Range 0～500Pa Pressure Sensor Accuracy ±0.5% F.S Air Flow Rrange 1 ~ 10L/min（Standard 8L/min） Air Flow Accuracy ±1.0% F.S Gas Source Compressed Air Air Pressure ≥0.3MPa Dimensions 350mm×260mm×360mm Weight 20kg Power Supply AC220V, 50HZ For more discount information on mask testing instruments, you can call 13539758284 or contact email: info@gbtest.cn

GBPI offers a comprehensive set of testing machine for surgical face masks and general-use medical masks. These tests are essential to ensuring performance properties are validated to support marketing label claims and to classify these mask types. For CE marking submissions, additional tests may be required depending on label claims. Summary of face mask testers Bacterial Filtration Efficiency (BFE) Differential Pressure Particle filtration efficiency Synthetic blood fluid penetration resistance for face masks Ethylene Oxide (EO) Residual Testing Face Mask Respiratory resistance testing mask elastic band testing Flammability test click to see GBPI face mask testers Applicable Standards ASTM 2100 EN 14683 NIOSH ISO 10993 Study Outline Bacterial Filtration Efficiency (BFE) The Bacterial Filtration Efficiency test determines the filtration efficiency by comparing the bacterial control counts to test article effluent counts. The test is conducted using Staphylococcus aureus as the challenge organism. After the filtration media is preconditioned, a liquid suspension of S. aureus is aerosolized and delivered to the filtration media at a constant flow rate of 28.3 liters per minute (LPM) or 1 cubic foot per minute (CFM). The aerosol droplets are drawn through a six-stage Andersen sampler for collection. The number of bacterial aerosol droplets contacting the filter media is determined by conducting challenge controls without filter medium in the test system. Challenge controls are maintained at 1700 – 3000 colony-forming units (CFU) with a mean particle size (MPS) of 3.0 ± 0.3 µm. This allows filtration efficiencies to be reported up to >99.9%. Click to see the Principle of BFE tester Particle Filtration Efficiency (PFE) The Particle Filtration Efficiency (PFE) test evaluates the nonviable particle retention or filtration efficiency of filter media and other filtration devices at sub-micron levels. This test is performed on face masks and all filter material that allows 1 cubic foot per minute (CFM) flow to pass through it. Also referred to as Latex Particle Challenge, this test is required for ASTM F2100 and is performed according to the ASTM F2100 and follows the basic principle of ASTM F2299. Applicable Standards ASTM F2100 ASTM F2299 more details of Particle filtration efficiency tester Synthetic Blood Penetration for Liquid Barriers The Synthetic Blood Penetration – Splash Resistance test is one of two synthetic blood resistance tests to determine a product’s ability to act as a barrier to blood-borne pathogens. The Splash Resistance test method challenges medical face masks with a fixed volume of synthetic blood directed at high velocity at the center of the mask. This test is required by ASTM F2100 and is tested in compliance with ASTM F1862, ASTM F2100, EN 14683, and ISO 26609. Applicable Standards ASTM F1862 ISO 22609 ASTM F2100 EN 14683 more details of mask Resistance against Penetration tester Flammability Test: The Flammability test proc...